Maxim-integrated MAX78630+PPM Evaluation Kit Manual de usuario

Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No

MAX78630+PPM Evaluation Kit User Manual 10 Rev 0 2.3.2 2V Delta-Connected Three-Phase Systems For Delta-connected systems, it is possible to meas

MAX78630+PPM Evaluation Kit User Manual Rev 0 11 1. Set Jumper J11 to position 1-2. 2. Set Jumper J15 to position1-2. 3. Connect the AC source

MAX78630+PPM Evaluation Kit User Manual 12 Rev 0 2.3.3 Neutral Current Measurement Considerations It is possible, in certain Wye configurations t

MAX78630+PPM Evaluation Kit User Manual Rev 0 13 2.4 Analog Input Jumper Descriptions The following tables describe the various EV board jumpers

MAX78630+PPM Evaluation Kit User Manual 14 Rev 0 3 Serial Interfaces Selection and Configuration The MAX78630+PPM has integrated UART, SPI (Slave

MAX78630+PPM Evaluation Kit User Manual Rev 0 15 UART/RS-485/422 Interface Configuration In order to operate the UART through the RS-485/422 trans

MAX78630+PPM Evaluation Kit User Manual 16 Rev 0 SPI/J16 Interface Configuration Table 15: Jumper Settings for Connecting on J16 Jumper Position

MAX78630+PPM Evaluation Kit User Manual Rev 0 17 4 Graphical User Interface (GUI) A graphical user interface (GUI) is included on the MAX78630+PP

MAX78630+PPM Evaluation Kit User Manual 18 Rev 0 4.1.2 Device Tab The Device tab shows to current firmware build as well as the temperature an

MAX78630+PPM Evaluation Kit User Manual Rev 0 19 4.1.4 Direct Tab The Direct tab allows access to the all the registers and can both read and wri

MAX78630+PPM Evaluation Kit User Manual 2 Rev 0 Table of Contents 1 Introduction ...

MAX78630+PPM Evaluation Kit User Manual 20 Rev 0 4.1.5 Command and Configuration Tab The Command and Config tab controls two frequently used regi

MAX78630+PPM Evaluation Kit User Manual Rev 0 21 4.1.6 Calibration Tab The Calibration tab is used to calibrate all the measurement channels. The

MAX78630+PPM Evaluation Kit User Manual 22 Rev 0 4.1.8 Energy Tab The Energy tab displays the accumulated power both into and out of the load. A

MAX78630+PPM Evaluation Kit User Manual Rev 0 23 4.1.10 Min/Max Tab The Min/Max tab is used to display the minimum and maximum measurements for

MAX78630+PPM Evaluation Kit User Manual 24 Rev 0 4.1.11 Alarm Tab The Alarm tab is a user-definable display of whatever parameters are required i

MAX78630+PPM Evaluation Kit User Manual Rev 0 25 4.1.12 Monitor Tab The Monitor tab is a running record of all the communications between the G

MAX78630+PPM Evaluation Kit User Manual 26 Rev 0 5 Schematics, Bill of Materials, and PCB Layouts This section includes the schematics, bill of m

MAX78630+PPM Evaluation Kit User Manual Rev 0 27 Figure 6: MAX78630+PPM EV Board Electrical Schematic (2 of 2) TitleSize Document Number RevDate:

MAX78630+PPM Evaluation Kit User Manual 28 Rev 0 5.2 MAX78630+PPM EV Board Bill of Materials Table 17: MAX78630+PPM EV Board Bill of Materials I

MAX78630+PPM Evaluation Kit User Manual Rev 0 29 Table 17 continued Item Quantity Reference Part PCB Footprint 23 4 R21,R40,R45,R49 0 603 24

MAX78630+PPM Evaluation Kit User Manual Rev 0 3 Figures Figure 1: MAX78630+PPM EV Kit Typical Application Diagram...

MAX78630+PPM Evaluation Kit User Manual 30 Rev 0 5.3 MAX78630+PPM EV Board PCB Layouts Figure 7: MAX78630+PPM EV Board PCB Top View

MAX78630+PPM Evaluation Kit User Manual Rev 0 31 Figure 8: MAX78630+PPM EV Board PCB Bottom View

MAX78630+PPM Evaluation Kit User Manual 32 Rev 0 6 Contact Information For more information about Maxim products or to check the availability of t

MAX78630+PPM Evaluation Kit User Manual 4 Rev 0 1 Introduction The MAX78630+PPM Evaluation Kit (EV kit) demonstrates the capability of the MAX786

MAX78630+PPM Evaluation Kit User Manual Rev 0 5 MAX78630+PPM Eval Board BurdenResistor UART USB 16 DIOsRS4855VHost PCThree Phase AC Sourc

MAX78630+PPM Evaluation Kit User Manual 6 Rev 0 1.4 Safety and ESD Notes EXERCISE CAUTION WHEN LIVE AC VOLTAGES ARE PRESENT! Do not connect test

MAX78630+PPM Evaluation Kit User Manual Rev 0 7 2 Installation 2.1 USB Driver Installation This EV kit includes an isolated USB interface for se

MAX78630+PPM Evaluation Kit User Manual 8 Rev 0 2.2 Powering the EV Kit Board The MAX78630+PPM EV board is normally powered through the USB port

MAX78630+PPM Evaluation Kit User Manual Rev 0 9 1. Set Jumper J11 to position 2-3. 2. Set Jumper J15 to position1-2. 3. Connect the Neutral fro