Maxim-integrated 73M1866B/73M1966B Reference Driver Manual de usuario Pagina 93
- Pagina / 98
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
UG_1x66B_015 73M1866B/73M1966B Reference Driver User Guide
Rev. 2.7 93
8.3 Platform Dependent Macros
The following macros are used in the driver code (defined in drv_config_user.h). These macros
must be defined according to the specific hardware environment and platform. It is expected that the use
of the driver will provide these macros workable with their environment.
/*================================================*/
/* INT =======================================*/
/*================================================*/
#define IRQ_NUMBER …
/*================================================*/
/* USER SPECIFIC FUNCTION ========================*/
/*================================================*/
#define M1966_SPI_MODE_16BIT
#define M1966_DETECT_OFH_POLARITY_CHG
#define M1966_DETECT_OFH_BATT
/*================================================*/
/* PCM CLK =======================================*/
/*================================================*/
/*================================================*/
/* define PCM clock initialization macro */
#define CONFIG_HOST_PCM(void) do { \
… \
} while(0)
/*================================================*/
/*================================================*/
/* FXO Reset =====================================*/
/*================================================*/
#define FXO_RESET(void) do { \
printk(“\nPerform FXO RESET\n”); \
… \
} while(0)
/*================================================*/
/*================================================*/
/* SPI =====================================*/
/*================================================*/
/*================================================*/
/* Define SPI chip select macros */
#define SPI_CS_SET_LOW(devNr) …
#define SPI_CS_SET_HIGH(devNr) …
/*================================================*/
#define SPI_WAIT_FOR_READY(status) do { \
… \
} while(0)
#define SPI_LL_READ_WRITE(connid,txptr,txsize,rxptr,rxsize) …
/*================================================*/
/*================================================*/
#define M1966_SPI_WRITE_BYTE(global,byte_ptr) do { \
int status; \
SPI_WAIT_FOR_READY (status); \
SPI_CS_SET_LOW (0); \
SPI_LL_READ_WRITE (byte_ptr, 1, 0, 0); \
- 73M1866B/73M1966B 1
- Reference Driver User Guide 1
- Table of Contents 3
- Figures 6
- 1 Introduction 7
- 1.3 Acronyms 8
- 2 Overview 9
- 2.2 Functional Overview 10
- 2.2.4 GPIO Support 11
- 2.2.6 Call Progress Monitor 12
- 2.2.7 Billing Tone Filter 12
- 3 Driver Service Interface 13
- and ioctl() 13
- 4 Country Specific Settings 14
- 5 FXO Events 15
- 5.2 Event Identification 16
- 5.2.8 M1966_RING_DETECT_END 18
- 5.2.10 M1966_OV_DETECT 19
- 5.2.11 M1966_OI_DETECT 19
- 5.2.12 M1966_OL_DETECT 19
- 5.2.13 M1966_LINE_STATE 20
- 5.2.14 M1966_DIAL_COMPLETE 20
- 5.2.15 M1966_DIAL_ABORTED 20
- 5.2.17 M1966_GPIO_INTERRUPT 21
- 5.2.18 M1966_ONH_DETECT 21
- 6.1.1 M1966_CH_INIT 24
- 6.1.14 M1966_CNTRY_NMBR_GET 32
- 6.1.20 M1966_SAMPLE_RATE 38
- 6.2.1 M1966_RNG_GET 39
- 6.2.2 M1966_POL_GET 40
- 6.2.3 M1966_BAT_GET 41
- 6.2.4 M1966_POH_GET 42
- 6.2.5 M1966_EVENT_GET 43
- 6.2.6 M1966_ERROR_CODE_GET 44
- 6.3.2 M1966_ATH1 46
- 6.3.3 M1966_ATH0 47
- 6.3.4 M1966_ATDP 48
- 6.3.5 M1966_ATDP_CANCEL 49
- M1966_PULSE_DIAL_PARAM_t 50
- 6.3.7 M1966_FLSH_CFG 51
- 6.3.8 M1966_FLSH_SET 51
- 6.4 Caller-ID Services 53
- 6.4.3 M1966_ENTER_CID_MODE 55
- 6.4.4 M1966_EXIT_CID_MODE 56
- 6.5 Ring Detection Services 57
- 6.6.1 M1966_MEASURE_START 60
- 6.6.2 M1966_MEASURE_STOP 61
- 6.6.3 M1966_MEASURE_UPDATE 62
- M1966_MEASURE_UPDATE_t read; 63
- 6.7 GPIO Services 64
- 6.7.3 M1966_GPIO_DATA 65
- 6.8 Loopback Services 66
- 6.9 Miscellaneous 67
- 6.9.2 M1966_BTONE_FILTER 68
- 6.9.3 M1966_CPROG_MONITOR 69
- 6.9.4 M1966_DEBUG_LEVEL_SET 70
- 6.9.5 M1966_TEST_CODE 71
- 7.1 M1966_COUNTRY_CODE 72
- 7.2 M1966_CNTRY_STRUCT_t 74
- 7.3 M1966_DEBUG_TRACE_MASK 75
- 7.4 M1966_LAST_ERROR_CODE 75
- 7.5 struct txrx_gain 76
- 7.6 M1966_PULSE_DIAL_t 76
- 7.8 M1966_THRESH_OVERRIDE_t 77
- 7.10.3 M1966_BTONE_FILTER_t 79
- 7.11.2 M1966_CPROG_MON_GAIN 80
- 7.12.1 M1966_GPIO_NUMBER 82
- 7.12.5 M1966_GPIO_DATA_TYPE 84
- 7.12.8 M1966_GPIO_CONFIG_t 85
- 7.12.9 M1966_GPIO_DATA_t 86
- 7.13.2 M1966_LOOPBACK_MODE 87
- 7.13.3 M1966_LOOPBACK_t 88
- 7.14.1 M1966_MEASURE_ENTITY 88
- 7.14.2 M1966_MEASURE_ACTION 89
- 7.14.5 M1966_IET_t 91
- 9 Related Documentation 95
- 10 Contact Information 95
- Appendix A – Country Codes 96
- Revision History 97
Relacionado con productos y manuales para Hardware Maxim-integrated 73M1866B/73M1966B Reference Driver
Hardware Maxim-integrated Teridian V.22 bis Linux Softmodem for 73M1822/73M1 Manual de usuario
(69 paginas)
(69 paginas)
Hardware Maxim-integrated 73M1822/73M1922 MicroDAA Software Architecture Manual de usuario
(10 paginas)
(10 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales